important: Nuts and bolts on your bike should always be tightened to the manufacturer's specifications.
Learn how to adjust the brake pads, cable tension and centering on v-brakes (linear pull).
Video updates
- 02:58 - Lubricate the pivot points with a few drops of Tri-Flow.
Today we’ll learn how to adjust v-brakes, which are otherwise known as linear pull brakes. For this job you’ll need a 5mm allen key, a phillips(+) screwdriver, a strip of sandpaper, and an optional cable puller.
Align Brake Levers
The first step is to set up your brake levers. Start by loosening the clamp, and then align them so that they match the angle of your arms when you’re riding. Once the angle is set, tighten the clamp. If you have smaller hands and your levers are hard to reach, you can set them closer by tightening the reach adjustment screw on most levers.
Remove & Inspect Brake Pads
Start by giving the cable some slack. Tighten the lever’s barrel adjuster in all the way. Then pull the protective rubber back and disconnect the brake cable’s quick release mechanism.
Then remove the pads. V-brake pads have two sets of positioning washers on each side of the brake arm. Be careful to watch how the washers are positioned so that you can re-install them correctly.
Inspect your pads. If they are worn past the indicator line, or have metal poking through the surface, you’ll need to replace them. If they look ok, use your sandpaper to re-surface both pads.
Adjust Brake Arm Tension
Now check your brake arm tension. The brake arms should have good spring tension, which makes them release when you let go of the brake lever. If there isn’t much tension, you may have to increase it on both sides. Undo both bolts one at a time, but don’t remove them completely.
You’ll notice a small piece of metal poking out the backside of the brake. This is the spring, and it slides into one of three holes on your frame or fork. Most brakes work fine in the middle hole. To increase your brake tension, move the spring into the top hole. To decrease the brake tension, move the spring into the bottom hole. Then tighten the mounting bolt.
Install & Align Brake Pads
Now re-install the brake pads, with the washers in the same order as they were before. Align the brake pads so the pad face is flat against the rim. V-brake pads are different from traditional pads in that they don’t require any toe-in. Both the front and rear of the pad should contact the rim at the same time. Because of this, v-brakes will sometimes squeak when applied. If you’ve re-surfaced the pads and they are still noisy, you may have to try a higher quality set of pads.
Take a look from the side to make sure the pad is in line with the rim’s brake surface, and not touching the tire or hanging off the bottom of the rim.
Align Brake Arms
With the pads installed, check the brake arm position. Both arms should be facing straight up and down when the pads are contacting the rim. If they are too wide apart, or two close together, you may have to re-arrange the pad washers.
One set of washers is usually thicker than the other. To correct brakes arms that are too far apart, make sure the smallest set of washers are closest to the pads. To correct brakes arms that are too close together, make sure the largest set of washers are closest to the pads.
Adjust Cable Tension
Now re-connect the cable and adjust the cable tension on the brake arm by pulling the cable through the pinch bolt and tightening. You’ll have to play with this adjustment until your brakes feel good. I like to have mine set so that the pads hit the rim when my lever is pulled about 1/4 of the way.
Brake Arm Centering
Make sure both pads now have equal clearance, and are not rubbing against the rim. Both pads should contact the rim at the same time. If not, you can adjust the centering by tightening or loosening the side adjustment screw with your screwdriver.
Alex Ramon
A bicycle geek since early childhood, spent his twenties as a mechanic in bike shops. His passions include flatland BMX, unicycles, cycle touring, mountain biking and road riding.
Related Links
- Park Tool: Linear Pull Brake Service
- Sheldon Brown: Direct-Pull Brakes
- Bicycle Torque Specifications
Recommended Tools
- Hozan 4th Hand Cable Puller
- Park Tool HXS-1.2 Hex Wrench Set
- Park Tool Wrench Combo Set
- Park Tool SD-Set Shop Screwdrivers
- Park Tool SK-3 Starter Mechanic Tool Kit
- Park Tool PK-3 Professional Tool Kit
Categories
- Brake
Discuss this topic in the Bicycle Repairs and Mechanics Forum
Adding brake to kids balance bike
Latest post 23 hours ago
Just looking to mount a brake to my kids’ balance bike. Any kits out there? Ideas? More of how to mount to frame. Simple U set up...
Read more
tried absolutely everything to fix these tight v-brakes that won't let up
Latest post 5 days ago
Obviously not trying to fit the wheel on without unhooking the brakes but it's just SO small, there's no movement. I've tried moving it to different pins by loosening the screws, i've tried lengthening the cable, but it just seems like up top the pads are so small- as i have to move the pads actualy all the way to the bottom not the top.It's a Trek steel 800. I like this bike, but i just undid a...
Read more
SRAM chainring 48/35 torque settings
Latest post 5 days ago
Hey, I lost a bolt on my SRAM chainring 48/35 and noticed that the rest were loose. What are the torque settings for this?...
Read more
Tubeless Sealant
Latest post 1 week ago
Hey folks!When you top off the sealant on your tubeless road bike, how much sealant do you add? I kind of eyeball it but I don't really know how much is the right amount.Thanks!...
Read more
NBD: 1990 Brompton Mk2
Latest post 2 weeks ago
Just picked up this little classic 1990 Brompton Mk2 with Sturmey-Archer 3-speed hub. Needs some TLC but all the important bits seem to be in reasonable condition with no signs of substantial rust on frame, rear triangle, or hubs. Not only do I look forward to learning The Way of The Brompton, but this means I'll probably be buying more tools. WINNING!WhatsApp Image 2024-05-11 at 1...
Read more
Specialized bicycle post issue
Latest post 2 weeks ago
Hi folks - this is my first post! The seat post on my year old Roll 3.0 is doing something annoying. It has a bit of play around the shiny collar just above the post clamp (see photo). I was told there is a plastic sheathing inside. Can this be fixed or is the seat post all one assembly?IMG_3153.jpeg (Size: 58.61 KB / Downloads: 64)...
Read more
9 speed chain on 8 speed bike
Latest post 3 weeks ago
All of my bikes are 7 or 8 speed and sometime in the past I bought a 9 speed chain for some unremembered reason. is there any reason not to use it on an 8 speed bike?...
Read more
Shimano Deore shifter
Latest post 3 weeks ago
[attachment=3051]I have a Kona Cindercone 8 speed from early 2000's. The right thumb shifter sometimes needs to be pushed once before it catches and moves the deraileur onto the next lowest gear. Is this something that I might be able to repair or is it likely I need to replace it. I have not taken it apart yet other than taking the top cover off which showed me nothing. I'm a reasonably compet...
Read more
interpreting serial numbers
Latest post 4 weeks ago
Can anyone help me to interpret the serial serial numbers on my Kona Cindercone (first pic) and Gary Fisher Tasajara (second pic). I've spent quite a bit of time online without discovering much. Every article seems to advise you to look it up on one of the online lookup sites but then fails to link said sites. In case the pix don't appear in the order that I attached them, the one with the whi...
Read more
Jeanne (Robinson) Omelenchuk’s custom 1960 road racing bike
Latest post 4 weeks ago
Check out the work that went into "Jeanne (Robinson) Omelenchuk’s custom 1960 road racing bike" here:http://classiccycleus.com/home/repair/museum-bikes-1945-to-1979/To whit: "George cast the aluminum hub shells himself, producing hubs that were extremely wide by the standards of the day (heck, they’re wide by today’s standards, and we pack 11 cogs onto modern rear hubs). The rims were dra...
Read more
How to disassemble SR Suntour xct-mlo fork
Latest post 1 month ago
Was given a 2013 GT Karakoram 4.0. Fork moves fairly well but starting to squeak and needs service. MLO works.How do I take apart the MLO side? Lots of videos show the SR Suntour xct with a smooth blue lockout cap. It has a lockring and you have to pry it up evenlyNot sure if this one is also a pry up. The notches look the same on both sides. Wrench fits on the spring/preload side and unscrews...
Read more
Problems with new 3x7 trigger shifter (ST EF51) on 3 side
Latest post 1 month ago
Hi, I am new to working on bicycle gears and am hoping to get some help determining if my new shifter has failed or if I just need to make some more adjustments.On the left side shifter, I am able to shift easily from 1st to 2nd, but when I tried to get it to go to 3rd, the chain would go up, but the shifter wouldn't lock into place. It would be great thumb exercise, but I prefer to fix it. I...
Read more
What tools have you bought recently?
Latest post 1 month ago
I'm slowly eliminated all LBSes in my area as options for servicing, LOL.The latest one has been struck off my list after watching, pained, their approach to removing the axle end caps from a hub with cartridge bearings.Suffice to say, I finally ordered a blind bearing puller kit and a bearing press kit.If you want something done properly, you have to do it yourself!Have you bought any nic...
Read more
Rear hub issue
Latest post 1 month ago
I have a 10-year-old 105 rear hub, and one of the pawls is acting up, I cleaned it and relubed the hub pawls but it still won't engage as fast as it did, like one of the pawls isn't working.I think it might be time to get a new hub. I would like one that engages faster but don't want to spend the money for something like the DT Swiss hub, what recommendations do any of you have for a hub? Or i...
Read more
Headset overtightening
Latest post 1 month ago
I have a Fondriest and could not get the headset to tighten without over tightening and then it will not steer properly because of heavy drag on the bars. I replaced the headset with no change so I replaced the steel fork with s Hylix carbon fiber bar and another new heatset and pinch steering head lock. Still it wont adjust properly. it acts as if the bottom headset bearing is too deep in the cup...
Read more
Post your question in the forum →
